Respirator Masks: Disposable, Half Face and Full Face

Updated 10 November 20265 min read

A respirator mask is breathing protection for dust, fume, gas or vapour. Safe Work Australia's silica code lists half face disposable, half face reusable, full face reusable and powered respirators, and puts a P2 disposable mask or a half mask with a P1, P2 or P3 filter in the band for a protection factor up to 10.

Types of respirator mask

The code defines the protection factor as the ratio of the concentration of contaminant outside the respirator to that inside it. Its table, adapted from AS/NZS 1715:2009, sets out the minimum protection factor each type gives when it is properly fitted and used.

Type of mask Filter Protection factor band in the code
Disposable half face P1 or P2 Up to 10
Reusable half face, replaceable filter P1, P2 or P3 Up to 10
Full face P2 Up to 50
Full face P3 Up to 100
Powered air purifying (PAPR), any head covering P1, P2 or P3 Up to 10 (P1) or up to 50 (P2, P3)
Powered air purifying, full facepiece or head covering and blouse P3 100+

Disposable P2 masks

Our 3M 8322 P2 valved masks are cupped disposable respirators with a Cool Flow exhalation valve, sold in a box of 10. 3M lists them for dusts, mists, smoke and fume, states that they comply with AS/NZS 1716:2012, and gives a protection factor of 10 x the Workplace Exposure Standard.

P2 is a particle filter class. Gases and vapours need a gas filter, such as the ABEK1P3 combined filter below, and our page on respirator filter types explains the letters.

Reusable half face respirators

A reusable half mask takes replaceable filters. The STS TS01 is a TPE half mask with a built-in fit checker for a negative pressure fit check, and a drop-down head harness so it can come off without removing a safety helmet.

STS approves two filters for the TS01: the YP3R particle filter and the YABEK1P3R combined gas, vapour and particle filter. We sell the TS01 as a kit with the ABEK1P3 filter and a kit for asbestos and silica dust, with spare ABEK1P3 filters and P3 filters.

Fit, facial hair and comfort

For silica work, Safe Work Australia's silica code says workers must pass a fit test before they first start wearing a tight-fitting respirator, including half face disposable, half face reusable and full face reusable masks and tight-fitting powered respirators. There is no one size fits all, and there can be no facial hair where the mask seals to the face.

Where a worker cannot be clean-shaven for valid reasons, the code says a powered air purifying respirator with a loose hood may be the only effective option.

Comfort affects protection too. The code says wearing an unpowered respirator for more than an hour, or during hard physical work, may become uncomfortable and lead to people removing it while still in a contaminated area, and that some safety glasses may interfere with the fit.

Choosing a mask from the Safety Data Sheet

Section 8 of the Safety Data Sheet should name the respirator. Safe Work Australia's code for preparing safety data sheets says vague information such as 'use respirator' is not helpful, whereas 'use half-face filter respirator suitable for organic vapours' is far more useful.

Check the mask or its box for the standard. For silica work, the silica code says to buy respirators certified to AS/NZS 1716:2012, and that compliant ones will usually show the number for this standard on the respirator or its packaging.

ChemMan, from Lupin Systems, keeps safety data sheets in one place and works out signage and PPE from what you store. For asbestos and silica work, see our asbestos and silica PPE checklist.

Respirators and filters we stock

Signs for the same area

Common questions

What are the types of respirator mask?

Safe Work Australia's silica code lists half face disposable, half face reusable, full face reusable and powered respirators.

Is a P2 mask the same as a half face respirator?

A P2 disposable mask is one kind of half face respirator. A reusable half mask takes replaceable filters.

Do respirator masks need a fit test?

For silica work, Safe Work Australia's silica code says workers must pass a fit test before they first start wearing a tight-fitting respirator, including half face disposable, half face reusable and full face reusable masks and tight-fitting powered respirators.

Can you wear a respirator mask with a beard?

There can be no facial hair where the mask seals to the face. Where a worker cannot be clean-shaven for valid reasons, the code says a powered air purifying respirator with a loose hood may be the only effective option.

Related guides

Sources

Checked against the sources above on 2026-11-10.

General information, not advice for your site. What protection a job needs comes from the Safety Data Sheet, the task and your risk assessment. The statements on this page are taken from the sources listed below and were checked on the date shown. Check the source, or ask your regulator.

Which respirator do your chemicals call for?

ChemMan, from Lupin Systems, keeps your safety data sheets in one place and works out the signage and the PPE from what you store.

See ChemMan